Plumbing Basics: A Must for Bathtub Installation
Plumbing Basics: A Must for Bathtub Installation
Blog Article
This great article which follows involving Installing A Bathtub is totally stimulating. Don't miss out on it.
Mounting a bath tub isn't precisely rocket science, but it does require strong plumbing, woodworking, and also sometimes, tiling abilities. Replacing an old tub with a brand-new one is additionally a moderately challenging project. If the old tub is conveniently easily accessible, the project can relocate easily; if you have to open up a wall to get rid of the old bathtub as well as place the brand-new bathtub, the task is a lot harder. In either case, the task is within a house handyman's skills, although you will require a helper to vacate the old bathtub and embeded in the new one. See to it you have qualified on your own for the task and fit trying it. Rather than working with a contractor to take control of a halfway-completed task, it is much better to consider employing one before you start. Chances are you may require an expert plumber to make tube connections.
This article will certainly help you mount a new tub in your washroom if you have actually currently gotten a new tub and don't require to alter the plan of your previous water system pipes.
Your tools and also material list should comprise the following:
Removing Old Taps
If you require to change old taps with new ones as a part of your installment, after that the first thing you ought to do is detach the water system. After doing so, turn on the faucets to drain pipes any water continuing to be in the system. The procedure of removing the existing faucets can be rather problematic due to the limited access that is often the situation.
Use a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will originate from the pipes. Once the supply pipelines have been eliminated, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from transforming during this procedure. Once the faucets have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing substance.
Prior to proceeding to fit the new taps, contrast the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the new faucets to fit.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will need a plastic port to stop damages to the string. One end of the connector fits on the plastic tail of the tap and the other end supplies a link to the existing supply pipelines.
If you need to fit a monobloc, then you will require minimizing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, place the faucet in the installing hole in the bath/basin guaranteeing that the washers remain in location between the tap and the sink. Safeguard the faucet in place with the manufacturer given backnut. When the tap is firmly in position, the supply pipes can be attached to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with normal faucet connectors. The previous type must be connected to the faucet ends initially, tightening up only by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Setting up the Bathtub
Utilizing both wooden boards under its feet, put the bath tub in the required setting. The wood boards are helpful in uniformly spreading out the weight of the tub over the area of the boards instead of focusing all the weight onto four little factors.
The following goal is to make sure that the bathtub is leveled all round. This can be attained by examining the spirit level as well as changing the feet on the tub until the spirit level reviews level.
To install taps, fit the bottom of the furthest adaptable tap adapter to the suitable supply pipeline by making a compression sign up with; after that do the exact same for the various other tap.
Switch on the supply of water and inspect all joints as well as new pipework for leakages and tighten them if needed. Fill the bathtub as well as also examine the overflow electrical outlet and also the normal electrical outlet for leaks.
Lastly, repair the bathroom paneling as explained in the maker's user's manual. Tiling and also sealing around the bathtub should wait until the bathtub has actually been made use of at least when as this will certainly settle it right into its final position.
Getting ready for the Setup
First of all, the supporting framework supplied with the bath should be fitted (if required) according to the maker's guidelines. Next off, fit the taps or mixer to the bath tub. When fitting the tap block, it is very important to ensure that if the tap features a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bath, it is additionally reasonable to fit a supporting plate under the taps device to stop pressure on the bath tub.
Fit the versatile faucet connectors to the bottom of both faucets using 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet with the hole in the bathroom. Use the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you use all of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath ought to currently prepare to be suited its last placement.
Tiling Around the Bath tub
In the location where the bath meets the floor tile, it is necessary to secure the joins with a silicone rubber caulking. This is essential as the installation can move sufficient to crack an inflexible seal, causing the water to pass through the wall between the bath and also the tiling, causing complications with moisture and possible leaks to the ceiling below.
You can select from a range of coloured sealants to blend in your fixtures as well as fittings. They are marketed in tubes as well as cartridges, as well as are capable of sealing gaps approximately a width of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with twists of soaked paper or soft rope. Keep in mind to constantly fill up the bath tub with water prior to securing, to permit the movement experienced when the tub is in use. The sealant can break fairly very early if you do not take into account this activity prior to securing.
Additionally, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise conveniently offered on the marketplace. It is a good idea to fit the ceramic tiles using water-resistant or water-proof sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We hope you enjoyed reading our piece on A Step-by-Step Guide to Installing a Bathtub. Thank you so much for spending some time to browse our content. Sharing is nice. Helping people is fun. We recognize the value of reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Protect your property, call! Report this page